Quick Answer
Use the EIRP (Equivalent Isotropically Radiated Power) Calculator to calculate EIRP from transmitter power, antenna gain, and feedline loss. In plain terms, enter Transmitter Power (W), Antenna Gain (dBi), Cable and Connector Loss (dB) and the calculator returns Equivalent isotropically radiated power with supporting values where the formula produces them.
This page is built for RF engineers, wireless installers, amateur radio builders, radar students, and network planners checking link and antenna values. It is most useful for link budgets, antenna dimensions, propagation loss, Fresnel clearance, received-power estimates, radar range screening, and impedance-match checks. The calculator keeps the units visible, shows the governing equation, and separates formula math from design approval.
Formula
The formula block above is the calculation used by the tool. The variable list below the equation defines the symbols in the same context as the calculator fields, so you can audit the math before relying on the result.
How to Use This Calculator
- Enter each known value using the unit printed beside the field. For this calculator, common starting inputs include Transmitter Power (W), Antenna Gain (dBi), Cable and Connector Loss (dB).
- Check whether the values come from a datasheet, a field measurement, a nameplate, a drawing, a standard, or an assumption.
- Read the primary output first, then review the secondary rows for current, power, gain, loss, impedance, duty cycle, margin, or design notes.
- Change one input at a time when comparing alternatives. This makes sensitivity checks easier and shows which assumption controls the result.
- Save or share the calculator URL after entering non-default values if you need a repeatable calculation record.
Inputs and Units
| Input | Unit | Default | Why it matters |
|---|---|---|---|
| Transmitter Power | W | 5 | Sets the electrical demand, signal level, or energy term that drives the calculation. |
| Antenna Gain | dBi | 6 | Represents a component property, coefficient, or model assumption that should come from reliable data. |
| Cable and Connector Loss | dB | 1.2 | Represents a component property, coefficient, or model assumption that should come from reliable data. |
Example Workflow
A practical workflow is to start with the default values, replace Transmitter Power with your project value in W, then update the remaining inputs from a datasheet, schematic, cable schedule, stackup note, field reading, link budget, or specification. After the result updates, compare it with an independent hand check and with any project limit that applies to the same operating condition.
For a quick check, the default inputs give you a complete worked context for EIRP (Equivalent Isotropically Radiated Power). If a small input change moves the answer sharply, treat that input as a design driver and verify its source before moving on.
Result Interpretation
The primary result is Equivalent isotropically radiated power. For RF, radar, and antennas, use the result as a link or geometry check, then verify antenna pattern, polarization, Fresnel clearance, cable loss, regulatory limits, fading margin, and installation conditions. A result that looks unexpectedly high, low, or sensitive to a small input change is usually a signal to check units, assumptions, boundary conditions, and the valid range of the equation.
Use this output as a transparent calculation, not as a hidden design decision. For safety-critical, regulated, high-power, high-frequency, or production work, document the input source, the formula assumption, the applicable standard, and the review path.
Assumptions and Limits
- The distance, frequency, gain, loss, polarization, impedance, and propagation model match the radio path being checked.
- Terrain, fading, clutter, weather, connector quality, mismatch, regulatory EIRP limits, and installation details can dominate the real link.
- The result is a planning estimate and should be confirmed with site survey data or measured RF performance for critical links.
- The calculator does not add hidden safety factors, derating curves, compliance checks, inspection requirements, or manufacturer-specific limits.
Common Mistakes
- Mixing dB, dBm, dBi, linear gain, MHz, GHz, meters, and kilometers.
- Ignoring feedline loss, impedance mismatch, polarization loss, fading, Fresnel obstruction, and regulatory EIRP limits.
- Assuming free-space propagation or ideal antenna patterns match an installed site.
- Copying the calculated value into production without checking the nearest real component, cable, trace, fuse, connector, antenna, optical part, or datasheet limit.
Related Calculators
- Antenna Dipole Length Calculator - Calculate total half-wave dipole length and individual element length from frequency and velocity factor.
- Antenna Quarter-Wave Monopole Calculator - Calculate quarter-wave monopole radiator length from frequency and velocity factor.
- Free Space Path Loss Calculator - Calculate RF free-space path loss from distance and frequency.
- 3-Phase Power Calculator - Calculate three-phase real, apparent, and reactive power from line voltage, line current, and power factor.
References and Further Checks
These references are useful for context and validation, but the calculator itself remains a simplified formula tool:
- FCC Office of Engineering and Technology - US RF engineering, spectrum, and equipment authorization context.
- ITU Radiocommunication Sector - international radio propagation and spectrum guidance.
For final engineering decisions, compare the result with governing codes, manufacturer data, site-specific measurements, lab testing, and qualified professional judgment.