Quick Answer
Use the Stripline Impedance Calculator to estimate stripline characteristic impedance from trace width, dielectric height, copper thickness, and dielectric constant. In plain terms, enter Trace Width (mm), Dielectric Height (mm), Copper Thickness (um), Dielectric Constant (dimensionless) and the calculator returns Estimated stripline characteristic impedance with supporting values where the formula produces them.
This page is built for PCB designers, embedded hardware engineers, RF layout reviewers, manufacturing engineers, and students checking board-level estimates. It is most useful for controlled-impedance planning, trace-current screening, via-current estimates, coax checks, and fabricator stackup conversations. The calculator keeps the units visible, shows the governing equation, and separates formula math from design approval.
Formula
The formula block above is the calculation used by the tool. The variable list below the equation defines the symbols in the same context as the calculator fields, so you can audit the math before relying on the result.
How to Use This Calculator
- Enter each known value using the unit printed beside the field. For this calculator, common starting inputs include Trace Width (mm), Dielectric Height (mm), Copper Thickness (um), Dielectric Constant (dimensionless).
- Check whether the values come from a datasheet, a field measurement, a nameplate, a drawing, a standard, or an assumption.
- Read the primary output first, then review the secondary rows for current, power, gain, loss, impedance, duty cycle, margin, or design notes.
- Change one input at a time when comparing alternatives. This makes sensitivity checks easier and shows which assumption controls the result.
- Save or share the calculator URL after entering non-default values if you need a repeatable calculation record.
Inputs and Units
| Input | Unit | Default | Why it matters |
|---|---|---|---|
| Trace Width | mm | 0.3 | Defines geometry, construction, or count data that strongly affects the result. |
| Dielectric Height | mm | 0.8 | Represents a component property, coefficient, or model assumption that should come from reliable data. |
| Copper Thickness | um | 35 | Defines geometry, construction, or count data that strongly affects the result. |
| Dielectric Constant | dimensionless | 4.2 | Represents a component property, coefficient, or model assumption that should come from reliable data. |
Example Workflow
A practical workflow is to start with the default values, replace Trace Width with your project value in mm, then update the remaining inputs from a datasheet, schematic, cable schedule, stackup note, field reading, link budget, or specification. After the result updates, compare it with an independent hand check and with any project limit that applies to the same operating condition.
For a quick check, the default inputs give you a complete worked context for Stripline Impedance. If a small input change moves the answer sharply, treat that input as a design driver and verify its source before moving on.
Result Interpretation
The primary result is Estimated stripline characteristic impedance. For PCB and transmission lines, use the result for early layout screening, then confirm with the board fabricator, field-solver methods, actual stackup data, copper tolerance, solder mask, and thermal environment. A result that looks unexpectedly high, low, or sensitive to a small input change is usually a signal to check units, assumptions, boundary conditions, and the valid range of the equation.
Use this output as a transparent calculation, not as a hidden design decision. For safety-critical, regulated, high-power, high-frequency, or production work, document the input source, the formula assumption, the applicable standard, and the review path.
Assumptions and Limits
- The dielectric constant, copper thickness, geometry, layer type, and temperature-rise limit match the board stackup being checked.
- Etch tolerance, plating thickness, solder mask, roughness, return path, airflow, adjacent copper, and connector launch effects are not fully modelled.
- The result is an estimate for review and communication, not a controlled-impedance coupon or qualification report.
- The calculator does not add hidden safety factors, derating curves, compliance checks, inspection requirements, or manufacturer-specific limits.
Common Mistakes
- Using a trace-width or impedance estimate without the actual PCB stackup.
- Ignoring copper tolerance, plating, solder mask, temperature rise, return path, and via barrel geometry.
- Treating empirical current formulas as final approval for safety-critical or high-reliability boards.
- Copying the calculated value into production without checking the nearest real component, cable, trace, fuse, connector, antenna, optical part, or datasheet limit.
Related Calculators
- Coaxial Cable Impedance Calculator - Calculate coaxial cable characteristic impedance from conductor diameters and dielectric constant.
- Microstrip Line Impedance Calculator - Estimate microstrip characteristic impedance from trace width, dielectric height, and dielectric constant.
- PCB Trace Width Calculator - Estimate PCB trace width from current, copper weight, temperature rise, and internal or external layer type.
- 3-Phase Power Calculator - Calculate three-phase real, apparent, and reactive power from line voltage, line current, and power factor.
References and Further Checks
These references are useful for context and validation, but the calculator itself remains a simplified formula tool:
- Global Electronics Association - PCB design, fabrication, and electronics manufacturing standards organization context.
- Saturn PCB Design Toolkit - widely used PCB calculator reference for comparison checks.
For final engineering decisions, compare the result with governing codes, manufacturer data, site-specific measurements, lab testing, and qualified professional judgment.